Chosen Solution

Tried to restore iphone 4s but keeps showing error 4013, any ideas? :) Best regards Tom.

hello my all friend i have same problem on my iphone 5s itune restore error 4013 after i change the u2 charging ic is fix. try it

I figured out how to fix this - this worked for both my and my friend’s iPhones.

  1. Connect to iTunes in recovery mode, start recovery.
  2. When you see the “Spinning wheel” on iPhone’s screen - EJECT THE CABLE IMMEDIATELY. Wait for 10 seconds
  3. Reinsert the cable - the restoration process will begin. Looks like Apple has a faulty algorithm that marks some iPhones as damaged even if they are not(or they simply want you to buy more new devices :)).

full open the phone connect only battery and charging strip and restore 100% working

When I had this error in the past it was with a NAND error (FlashMediaAndKeepout………….. PROVIDER <PTR….) It was the SCREEN.

Hey Tom, This is a solution to your problem: http://support.apple.com/kb/TS5314 Tell me how it goes. Hope it helped. Have a nice day!

4013 on 4s is usually the nand flash or baseband chip gone bad. Not worth fixing a 4s these days when it comes to those issues.

I had this exact problem on my iPhone 5c. Error 4001 when I tried to restore and error 4013 when I tried to update. After some quick google searching, I then REMOVED THE SCREEN and tried the process again. 100% working now. It’s apparently an LCD issue.. usually caused by a faulty Proximity Sensor.

Solution 1: Reboot your iPhone Solution 2: Check Out the Faulty Cable/Port Solution 3: Is Wi-Fi Network Working Properly? Solution 4: Clean Up Your iPhone Solution 5: Restart Your Computer, Reset Your iPhone…. You can click the tutorials for detailed information: How to Fix Error 9, 4005, 4013 or 4014 in iTunes/3uTools?

IF you have a MACBOOK it’s tested just restore it in your MAC

Repaired lots of iPhone 6 recently and error 4013 is being caused by a faulty front camera ribbon- there’s a few components on the one ribbon. Replace it and problem solved or if your stuck disconnect it and reboot the handset, it’ll boot up again. Then reconnect it whilst the handsets on and it’ll stay on but if it does happen to power of it won’t boot up again as it’s picking up the faulty ribbon on its boot check. So replace it when you can!

Had replaced my 6s plus screen and disconnected the screen and worked like a charm

This method worked for me http://feedstech.com/5-ways-fix-itunes-e…

I would say disconnect the the last cable to iPhone logic board and try again!! Or if you have a old 4s screen try it but don’t hook up last cable and see if that fixes it

Error 4013 I due to security software issues . uninstall ITUNE your computer completely restert your computer and reinstall the iTune latest version try again your iPhone restoring …,…same problems iPhone 5 5s iTunes error 4013 is hardware change the charging connected ic and compass ic is fix .and try it I am from pk

I found a solution that worked for me. Tested with iPhone 5 GSM. Here’s the fix http://bit.ly/1P3yQDM

I have an iPhone 5c that worked well But it did not work network constantly to pen that is looking for , and last night I went to reset to factory settings and has failed , threw me a mistake 4013th Did he know who the problem , I put a new screen and new battery Update (03/05/2016) I have an iPhone 5c which had not worked networks , and last night I went to reboot I got stuck at half load, I threw the error 4013 , was helpful before and everything was working normally Network did not work , constantly it says that asks , I was trying to do over the item But in vain , And he put a new screen , home button and battery

1: try change battery and charging port to a new one, 2: try put on a new or secind hand screen, 3 try another cord: 4: make sure itunes is the newest version

Error 1405,4005 on iPhone 6,6 plus. Complete solution follow the steps bellow _ Remove the Top metal plate of charger and battery connectors, Connect the phone with itunes and start restore for restoring. For this step you need to have a heat gun low down the heat to 160 and make the air to high presser start heating up the battery and charger port connectors warm up. when the phone goes off wait for a while and when you see the restoring precess give it more heat for a few minutes,Then release the heat Gun and see the magic. 100% solution.

This may or may not be useful to those having issues: I have an iPhone 6s, and got the dreaded 4013 error. Tried many things–restarting phone, computer, etc., reconnecting cords to different ports, disconnecting them at pivotal moments. The last thing I thought to try was to take the phone out of its battery case (which I got fairly recently). That did it–made all the difference. Update went smoothly after that. This may not be the same thing plaguing others, but it definitely made it work for me.