Posts

Chosen Solution “I have an Alcatel one touch and every once in a while it will go black then send me to my lock screen Hi abdul zarid. Try resetting the phone with a factory reset and then use it this way for a while to see if it still happens. If it still occurs you have a hardware problem and need to get it repaired or replaced under warranty. If it doesn’t happen anymore a downloaded app may be the cause of the problem....

Chosen Solution washer stops part way threw cycle when still full of water The 5 most common part(s) or condition(s) which contribute to the symptom Washer stops mid cycle are listed below: Lid Switch Assembly If the washer stops mid cycle the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity....

Chosen Solution My phone won’t charge unless it’s turned off Hi, What are the specifications of the charger that you are using? It should be written/stamped on it. Look for output values, especially the mAH or A rating. If you are charging the phone using a PC’s USB port, be aware the while it can charge the phone it cannot both run the phone and charge it at the same time, as it only can supply 500mA (0....

Chosen Solution My car 2005 Pontiac Grand Am tends to overheat. I’m not sure the radiator fans are working. Is there a way to check them to see if they are operating? Dennis Brunner, the fan doesn’t come on until approximately 210°. Check to make sure your fans come on. It should come on whenever the AC is on, or when the engine is hot. If it doesn’t come on when you turn on the a/c, the fan relay is probably bad....

Chosen Solution I have 2006 yeared honda civic, when i turn engine on it has sound, after heatting engine it starts turning off i can’t go forward or backward faster than 10-15 km, even if i push gas on all power itisnt going faster, and car is turning off time after time. What can be problam? There could be a multitude of problems at play here . The best and quickest way would be to read the obdII codes then post them here and we can help....

Chosen Solution While watching tv, it will shut off by itself. I have to unplug it wait a few minutes and plug it back in again, then it works again for awhile, then shuts off again. I have no idea why. I have it plugged into a power surge protector. I was gone away on vacation for 2 weeks and it was previously working fine, until I returned home. Now it shuts off by itself....

Chosen Solution I just dropped my iphone, now the telephoto camera not working and the camera module get overheat (just the telephoto camera module). Do i need to change the camera or its the IC problem? please help Unless you have the tools and skills required to troubleshoot the camera driver circuit, the easiest thing to do is to replace the camera module with a known-good module (or new) to see if the problem persists or not....

Chosen Solution Hi, My CD Burner (only used a couple of times) as above stopped working a couple of weeks before my years warranty ran out. contacted apple who replaced it with a new one. Brought it home tried it once to check all was well. It worked. 11 months later went to use it, it had the same problem as before with the warning of “the disc can’t be burned, because the device failed to calibrate the laser power level for this media”....

Chosen Solution 2000 Ford Expedition (Eddie Bauer edt.) My trucks cigarette lighter keeps blowing the 20 amp fuse roughly 24 hours after I replace it. Why does it continue to keep blowing? First try plugging something else into the socket and see if it blows. If not, replace the heating element in your lighter. http://www.autozone.com/electrical-and-l…

Chosen Solution My phone is working good, but when i receiving a call or touching its not working properly. i try to touched very hard. i made complete reset also it’s not fix it. please Support me. Thank you. (Sony Xperia XA) Hi, did you drop your XA before? How long have the touch problem been? When you touch hard, does it work? It seems like the the screen flex was loosen, you can try open it and reconnect the flex cable....

Chosen Solution Hello! I have a replacement screen that looks great and intact. No issues with touch at all. However, once I put the iPad back into its case (STM, has magnets) and close the cover, Siri will trigger. Any suggestions? There are two SmartCover magnets on the inside of the digitizer (see Step 49 - 52 of this guide). Did you migrate them over to the replacement screen? If so, it is possible they became dislodged or incorrectly positioned....

Chosen Solution My tablet will freeze randomly while I’m using it! I have turn off the display for a few seconds then push the home button and its okay for a few minutes before it freezes again. In a ten minute period, it’ll freeze about 8-10 times. I have shut it off and then back on, and reset the tablet to factory settings. Neither of them fixed the problem. Also, I won this tablet in a competition so I have no warranty....

Chosen Solution Phone won’t turn on, only get black screen, and able o get into DFU mode, iTunes sees phone in “recovery” mode. I want to get it to boot so I can use Disk Aide to get data off the phone. It has the red water damage dot in dock connector. I have tried tiny umbrella to kick it out of DFU mode, and then it disconnects from my Mac, and still has black screen....

Chosen Solution where could I buy a new one beam splitter ,because the coating of beam splitter does not exist and when view through viewfinder the triangle from the rangefinder is not longer visible , and i try using a piece of blank 35mm color negative that has been processed which I put behind the beam splitter, and followed these procedures the triangle of beam splitter is visible , but appears as double triangle, probable first triangle is a reflection of 35mm colour negative film procesed , and the second triangle is reflection of beamsplitter glass....

Chosen Solution i have 20 hp twin cy briggs engine and when i take the choke off the engine stumbles then stalls . what do look for ive rebulit the carb and still the same results. i replaced the carb and still the same results , whats next @lawnmowerman, paul , Some things to check for. Bad fuel(install fresh good fuel), possible weak fuel pump(if equipped), pinched/collapsing fuel hose, clogged fuel filter(unhook spark plugs, remove fuel line at carb....

Chosen Solution ‘‘‘Hi I have LG DVD plater that’s connect to the TV if I play music disc it is work but when I want to play video it’s show disc error why? ’’’ Ali, this is most likely caused by a dirty/misaligned laser. I’d start by cleaning it with a commercially available disk drive cleaning disk. If that does not work, you may have to disassemble the player and clean the lasers manually....

Chosen Solution I press the power button, but nothing happens. How do I remedy this? Hi @ Patricia Thomas, You have two options. a) Try a factory data reset and check if this resolves the problem. Be aware that a factory data reset will erase all your data and downloaded apps. It will restore the tablet to its’ default factory condition (or last system updated condition) Therefore it is important to backup the tablet before performing a factory data reset if you do not wish to lose all your data and downloaded apps....

Chosen Solution If I unplug my HDMI and power to my x-box directly, will it were down my port on my x-box? (Every week.) yes it can wear the hdmi port down i replace hdmi ports all the time in my shop ive never seen a power port get worn so i would say the power port will be ok but id look out for the hdmi constantly plugging and unplug can leed to the port being damaged...

Chosen Solution I have old iBook g3 white. i also have a white iBookg4 and my question can i take the ram out of the iBookg3 and put it into the iBookg4? i need more memory is why im asking. Hi! No, unfortunately, the memory used in iBook G3s is different from memory used in iBook G4s, and will not work. It is physically different and will not fit in the memory slot....

Chosen Solution while driving my driver side wiper quit working. It turned out to be the linkage under the cowl. I replaced the linkage, but now the wipers park in the middle of windshield. any suggestions? @yippyskippy what vehicle is it? when you replaced the linkage you had the windshield wiper motor turned of before so that it “parked” in the right position? In my experience an s depending on the car make and model, you may be able to adjust the wiper arm by removing it and then repositioning the arm to the correct “stop” position....