Chosen Solution I replaced the joystick on my 3DS 2015. After reassembly my device won’t power on. What should I do to resolve this problem? A common mistake when reassembling the 3DS is forgetting to connect the power button ribbon cable when reassembling. Ensure that the ribbon cable, which goes from the power button in the bottom right of the device to a connector in the middle of the logic board, is connected....
Chosen Solution I’ve attempted to charge my phone with two different chargers, but the highest percentage the phone will reach is 2%. I tried to clear any debris from the charging port, but there is none. What is wrong with my phone? If you are using it with a Mac, download and install and run Coconut Battery. It has an iOS feature that can give you detailed information on the condition of your battery when you connect it to your Mac....
Chosen Solution The battery on my macbook wont charge. It works with the AC adapter plugged in. However, it shuts down immedeintly if unplugged. The battery status says it is not charging. There has never been any water damage and I have updated as much as possible. I read online that unplugging the device, taking out the battery, and holding the power button down for 10 seconds resets and supposedly fixes this issue....
Chosen Solution How can I get my Android phone Oppo F11 pro see the Drone Wifi signal? I have tried for the past 3 days and the drone doesn’t seem to have it’s wifi visible for my Android to see. I need help please. if there are preferred compactible phones I will like to know. Did you check of your drone is accessible from other phones? If so - check if your drone’s wifi is 2,4 GHz signal and not 5 GHz, since if you have an older phone it may not properly support 5 GHz....
Chosen Solution I replaced the screen a couple months ago. The screen works fine but every now and then the touch doesn’t respond to touch and I have to reboot the phone for it to start working. It happens every couple days. It’s a defective screen, and if the ribbon cable for the screen is not held in place with some sticky / scotch tape this issue can occur.
Chosen Solution What type of Triac is used on the 8200? I’ve burnt mine out and can’t read the number. I have had the same trouble with control board burned out. I bought the rotary tool 2 months ago, in France and live in Brazil. So, sending the machine to US (and have it back) I believe will be so much expensive. I already have the P/N of the board and will try to buy it frm some Dremel service....
Chosen Solution My speedometer went all they way around on my 2001 Acura. What do I do? Hi, Does it do this only when the car starts moving or when you first turn on the engine? Does the meter needle stay hard over or move at all? Is the tachometer working OK? Looking an the electrical wiring section of the repair manual for the car (see diagram below for the speedometer circuit), it appears that it operates from the main circuit board in the instrument cluster and that the only signal coming in is from the PCM/ABS/TCS control line, which supplies the information presumably for both the tachometer and the speedometer....
Chosen Solution Hi guys, I’m working on a 2015 Macbook Air 13”. Everything works after the spill except for running the computer on battery. Oddly enough, the computer shows that the battery is present and has 70% charge but it will turn off once I unplug the charger. Does anyone have schematics for this macbook that may aid in narrowing down the issue? Let’s start off by testing the battery. Complete the guide I provided below, and make sure to upload an image of the coconutBattery window to your existing question!...
Chosen Solution I spilled a lot of milk on my chrome book and it worked after that for 3 days and then it stopped working and idk what to do Hi @ben18183 Do not try to charge or to turn on your laptop! Disconnect the charger (if connected) and then disconnect and/or remove the battery as soon as possible to minimize any further damage to the laptop caused by the action of liquids on electronic components....
Chosen Solution Hi all, I spilled water on my laptop earlier this morning, and while I thought I had completely shut it off it turns out I had only restarted it and I realized about 30 minutes later. Did this mess up any chances of recovery? Or should my laptop be fine if I leave it alone for 2 or so days? Treating liquid damage on electronics is like treating a stain on your favorite shirt in that you must treat it immediately....
Chosen Solution started getting very hot (210 degrees) while performing same task that would normally raise it to 170-180. what could cause the sudden increase? Most likely your HD SATA cable is breaking down so it’s fighting though a CRC battle between the drive & CPU every time you open or save a file. Here is the IFIXIT guide: MacBook Pro 13" Unibody Early 2011 Hard Drive Cable Replacement and you want to use the newer version of the cable: MacBook Pro 13" Unibody (Mid 2012) Hard Drive Cable - Apple P/N 923-0104....
Chosen Solution When startup, the loading bar reach 70%. The monitor turns to save mode and blank screen. Press monitor power button. Turn off and then turn on again. The login screen is appeared. How to fix it? 更新 (2019年07月01日) cannot fix the issue. First try starting in Safe Mode to see if you have extension issues. Boot up holding down the Shift key. Next see if you can boot to the repair portion....
Chosen Solution Hello everyone! While attempting to remove the screw to my SSD I stripped the screw really badly. Is there anyway I can get this out? Im open to any options that wont result in destroying the computer. Thanks! Picture of screw: You can use the extraction pliers on this screw: Screw Extracting Pliers Check out this video for some ideas.
Chosen Solution Hello There, Can you please help to get rid out of my problem, My roblem is i have a lava falir z1 a spreadtrum phone, i have flash it’s stock rom via spd research tool 4.0.0.01, but after flash the phone always going recovery mode, and says E: error failed to mount /cache? can u plz help me out? See instruction Download android latest usb driversetup this driverI thing your smartphone chipsetDownload 7715 Nand cpu driver For details click here: spd usb driver...
Chosen Solution So my phone is almost 2 years old and it just shuts off at any given time if i’m not charging it and then won’t come back on until i charge it again. Try replacing your battery.
Chosen Solution Coolant is boiling out of the coolant reservoir after the car warms up. However there is no white smoke out of the exhaust so I don’t think its a head gasket. There is a very small leak on the bottom radiator hose but its only like a drip every 2 minutes or so. I just installed this new radiator because the old one was cracked and I was hoping i would have no more problems....
Chosen Solution hello, i just received an ipad 4th gen. i charge it for hours, take off charger (its in dfu mode), i plug into itunes click restore and update. it will extract the software, but when it begins to restore, it hangs on the apple logo and the loading circle on the ipad freezes. my computer will then wait on the ipad for 10 min or so and then say ipad not responding....
Chosen Solution It looks rectangular and changing color when I was browsing the internet. It is possible you have a loose LCD cable or a faulty LCD. Or, I could even be the video card. Try connecting it to a TV and seeing if it does the same thing. If it does, the video may be bad. Otherwise, try opening it up and reseating the LCD cable. If that does not work, the LCD may be broken....
Chosen Solution my turn signal is not working but hazard light is working. how do I fix this problem. Cross posted from your other question: Hello, it depends on the year of W123 you have. The very early models with the “big” hazard flasher switch that you push in to turn on the relay is part of the switch. You simply replace the switch as one unit along with the relay....
Chosen Solution The dust shroud acts as if it is clogged and the dust collector is not doing its job. I have the same exact sander and this could possibly be a simple fix and your going to need something that blows air my preferred method is an air compressor but air in a can works to. You going to want to take the dust bag off and there is a gap on the front of the sander where there are metal fins that’s the area where gunk builds and all you have to do is blow compressed air into that area....
