Chosen Solution My Vizio e550i-b2 screen went black w/ sound. I replaced all the component boards in the tv, and now my picture is messed up. I did 2 factory resets to no avail. The tv is not even 2 years old. @edg81 could be main board issue as well as a panel issue. Since you replaced all the boards, try to replace the mainboard with the one you had and see if it changes....
Chosen Solution The touch is operstional but while using it the devices starts glitching and touching other things to the left and middla of my screen Hi, Try starting the tablet in safe mode to check if it works normally. If it does then the problem is being caused by a downloaded app. The trick is to find out which one. If it is still no good when in safe mode, it may be that the digitizer is failing....
Chosen Solution When I’m a certain distance away from the charging base, my call sometimes drops. Hi, Sometimes bad signals can be cause by interferences in your home. To fix this issue you can make sure that your charging base is placed at a higher point in your home to insure less resistance for the signal. Also you can check your antenna to make sure it is working correctly and if not refer to the replacement guide to replace it....
Chosen Solution I bought a 1970’s era Hobart KitchenAid K45SS and proceeded to disassemble it, replace a broken gear, paint the exterior, clean the motor with electronics cleaner, repacked new grease and put it all back together. Prior to this project the mixer worked but was noisy. Now, with the power switch in the off position, as soon as I plug it in the motor starts turning. It operates on all speeds but will not turn off....
Chosen Solution The screwdriver will not turn when I pull the trigger. The work area LED is coming on. Hi Mark, According to your description, the work area LED light is coming on when pulling the trigger. In result, this indicates that the screwdriver battery has not yet been depleted. First, remove any load from the screwdriver (if any) and test for rotation again. If the screwdriver rotates after removing the load, it is possible that you are over-torqueing the screwdriver; select another torque setting by rotating the torque selector located just behind the bit socket....
Chosen Solution Why isn’t my HP Photosmart C4740 (Printer, Scanner & Copier) not printing? It has a new black cartridge and half full color cartridge. The 1st print came out light blue/grey even though I chose black print. Now it acts like it’s printing but paper comes out blank. Take the cartridges out & clean the contacts with Q tips. Have your Q tip damp but not over-soaked with water. Then dry the cartridges with the dry end of a Q tip and then with a soft cloth....
Chosen Solution Washer rinses, and when it goes to spin cycle, the spin light comes on, but it does not spin. Washer’s wash light comes on, but does not rewash. Help! Cause 1 Lid Switch Assembly The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity....
Chosen Solution I am having trouble rebooting my laptop (1.67Ghz,120HD,2Gb RAM,MacOs 10.4.9 or 10.4.11) Have taken RAM out, swapped slots, done the PMU(?) reset, holdiing power key for 5-10 sec, ect. All with no luck. Came back from holidays & it wouldnt get past the DVD check. There is NO Vid display at all, not even a flicker. the DVD seems be trying to eject maybe a DVD. Try starting up holding the option key down to see if there is a system disk in the drive....
Chosen Solution Hello, I disarmed the equipment to install a new keyboard, all works fine but now it says “wi-fi, no hardware installed” But the bluetooth works wich is in the same Wi-Fi card installed in the computer How can I fix it? Thanks for your help Could be WiFi card (WiFi functionality can fail on the card, but Bluetooth can work fine, and vice versa), I/O cable (make sure it is connected properly) or I/O board; difficult to say for sure without trying test parts first, but firstly make sure there is no dust inside the I/O cable connector preventing a full connection
Chosen Solution My wifi is not working and it is definitely hardware related. Is it the logic board or communications board that needs replaced….? Aidan, the WiFi is part of the Communication board. The instructions are here and the parts are relatively expensive as well, do a Communication Board search on Google. Of course make sure that you antenna wire is properly installed and not disconnected etc. I am sure you have tried the Apple solutions as well, http://support....
Chosen Solution Hello, i look for a Wifi Modul Dual Band 5 Ghz, because my Samsung support only 2,4 Ghz but my Fritz Box 7270 V3 support both 2,4 and 5 Ghz. Who can help me to find out this Modul and maybe also replacement? Thanks for Help / Support regards Ron You are right this Samsung Model only supports 2.4 GHz Wifi frequencies according to GSMarena and Samsung phone specifications on samsung website as well....
Chosen Solution I dropped my phone from no more than 1 foot off the ground, but it landed at a terrible angle on some rocks and received a chip in the lower right hand corner + a hairline fracture that extends about an inch across the bottom of the screen. Since then, the screen will almost constantly flicker and glitch, sometimes spontaneously turning black or shutting off. When it’s doing this, it may respond partially to touch or not at all....
Chosen Solution My wife just cracked the screen of her Series 2 Apple Watch, so I just ordered her a new Series 4. I don’t have an Apple Watch myself, so I figured that maybe I’d just fix her old one for myself to play around with. The problem is, the cost of the Series 2 display/digitizer is way too high to make it worth repairing. The Series 1 display is much less expensive, so for a situation like mine where I don’t really care about it being the best possible display, will Series 1 install properly in the Series 2?...
Chosen Solution If I purchased a Dell laptop with Windows 10 installed by Dell and for some reason I need to replace windows 10 would I be able to obtain a copy free from Dell to fix my problem? If not from Dell, could I obtain a copy free from Microsoft? Yes. You can grab the free download from Microsoft. Windows 10 doesn’t use a key. Instead it uses a unique identifier in your motherboard for activation/reactivation....
Chosen Solution Power is going to main board but will not power on. Open the back and check the diagnostic LEDs located in the center of the logic board and tell us what they show. Also look at the capacitors (cans) and see if they show signs of swelling and or corrosion, let us know and we can go from there.
Chosen Solution why won’t my iphone 6 plus let me slide to open flashing screen unresponsive Well let’s go ahead and try a force restart, and see if that fixes the problem How to Force Restart an iPhone 5 Yes I realize this is for an iPhone 5, but the principle is the same
Chosen Solution Where can I find a website that sells reliable and high-quality iPhone spare parts to order? Hi @ibaabood , Did you check out the ifixit store? ebay and ali express. just make sure to check the reviews and you should be good.
Chosen Solution Hello! I got an iPhone 7 plus. It was working fine but after I updated the ios (from 12.0.1 to 12.1.4) the front speaker which is the earpiece creates distorted /crackling sounds specially when I’m listening to music. What could be the problem? The issue happening after the update could be a coincidence. Usually when you have crackling or distorted audio from the ear speaker on a 7 or 7 plus, your phone is suffering from audio ic chip issues which is only repairable by soldering a new audio ic chip....
Chosen Solution hey yall, I’m having a dilemma… I’ve taken my mac apart, scrubbed it with a toothbrush and 99% isopropyl alcohol, but there’s still a residue everywhere on my logic board (and case). the milkshake seemed to combine with the dust on the inside of the mac, so hmph. I can scrape it off, if that counts. I can’t afford a £1000 ultrasonic cleaner, so any tips on how to get this removed?...
Chosen Solution Hi, I recieved an ex-display Kenwood KMC560 today. And I tested the speeds with the whisk and water in the bowl. I noticed strange smell when I was changing the speeds. The smell is slightly metalic. I also noticed a bit of oil on the sides. The smell is a bit similar if you run an old motor. Is that normal? If it going to damage the product if I continue to use it?...
