Chosen Solution I have a phone that came back from a customer claiming no sound on calls. I verified that it was audio ic. I did the repair, but now it is not turning on and only charging at 0.6A. I’ve tried a new battery and charge port. It still won’t turn on or charge past 0.6A. I’ve left it on the charger long enough for it to show that it’s charging, but it never turns on or shows that it’s charging....
Chosen Solution Hello everyone , So I bought a used iPhone 8 plus from ebay but when I power it on I noticed the left corner of the screen looks dim so should I buy screen replacement or could the motherboard be damaged? This is a faulty component on the backlight circuit. It is becoming an increasing problem with the 8 plus. Usually it is a small resistor which has failed causing the screen dimming in that exact place....
Chosen Solution Hi there I’ve a problem with my 24" LED cinema display. The display is constantly switching on and off. I’ve used the Apple Technician Guide to check out whats wrong. I was going step by step trough it. What i found out is: The volltage between TP11 and GND is not stable. It moves constantly between 22.7 - 23.2 VDC. Also the connector cable voltage (Pin 1 and GND) from the power supplay is moving constantly between 14....
Chosen Solution My GE Profile Spacemaker 2.0 started to hum a bit louder and now makes no heat. I followed the GE troubleshooting flow-chart and it points to the magnetron, but the resistance checks (continuity pin-to-pin, open pins-to-case & no sign of any arcing or cracks in magnets). The HVT (hi volt Xfmr), Cap (capacitor) Xfmr, and diode all seem to be okay although my cheaper DVOM shows diode open both ways ....
Chosen Solution With the steaming knob in the off position and the steaming button also off. Water is dripping from the steaming wand when the machine heats up. When I start to make an espresso water then pours out the wand. I get about 125ml of water per espresso. The espresso also tastes weaker and has less cream. I am using the same coffee I have always used. I have also recently cleaned the espresso boiler plate as per the manufacturers guide and also descaled the machine....
Chosen Solution Usually (about 50%) my laptop monitor became black when I turn it on or sometimes between working …..but when this trouble fall the laptop continue working e.g. when I watched a movie suddenly the monitor becoming black but the movie be continued and the touchscreen works without any problem ,because I can pause or play movie with touch it when the monitor is black Hi, Try shining a torch at an angle close to the screen (when it is black) to see if you can detect a display at all....
Chosen Solution I bought a new battery from ifixit. I installed it easily and it was charged 70%. When the battery was low I tried to charge it but it was not charging. I did all types of reseting and still not charging. any ideas? I’m sad to say you have a charging logic issue on your logic board! The battery is responding and the charger is as well. But the power ‘Charging with’ is stuck at ZERO!...
Chosen Solution When I plug in the charger to the charging port I literally have to hold it at a weird angle to get any charge at all. If I just let it sit how it is supposed to, my MacBook just shuts off because it won’t charge. Is this something I can just clean or do I need to have it fixed? Also how much would something like that cost?...
Chosen Solution Will not turn on or charge up at all Hi, Try the following, Disconnect the charger if connected, then remove the battery from the laptop. Press and hold the power button on the laptop for about 15 seconds then release the button. Reconnect and switch on the charger (leave the battery out at this stage). Start the laptop by pressing the Power button. If the laptop starts, allow it to boot all the way to the Windows desktop....
Chosen Solution Hey guys . I am trying to install my stylus pro on windows 10 but van t locate any useful stuff to do Any idea? This is a very old printer. I don’t think Windows 10 is supported. I looked around on Epson’s website, they don’t have a downloadable Windows 10 driver. Go To control panel –> Devices and Printers in Windows 10. If “Add a printer” doesn’t have your printer on the list, and if you don’t already see your printer, it may be time to upgrade to a newer printer or downgrade your version of Windows....
Chosen Solution Kendall 4/5 reader won’t fully powered on. I’ve unplugged recharged green light goes on but the one bringing back up it only goes halfway then turns off again Hey Gail, Have you tried holding the power button for 90 seconds? If this doesn’t work, it will probably require a new battery. The battery can be brought from eBay and YouTube can show you how to change it.
Chosen Solution There is a different connector on the 2nd drive kit than on my optical drive that has the regular SATA connector. On the photo the lower drive is the optical drive, the top one the dual hard drive kit. How to solve this? Taking a look at your order it looks as though you accidentally ordered the PATA instead of the SATA enclosure. I will go ahead and reply back to your email to setup a return....
Chosen Solution So I’ve looked everywhere and can’t find the part I need, mostly because the aftermarket buttons flood my search. However, I need the plastic piece everything screws to. Not the shell, but the part that houses the trigger springs. I broke one of the little pastiche pieces that hold my spring in place. Any help is appreciated. You’re probably going to need to buy a boneyard controller to salvage the part you need off it if you want to stay OEM....
Chosen Solution The device will only work when plugged in. I have tried different plugs, cords, and outlets. as soon as it is unplugged it shuts off and does not turn on. It will also lose connections with a phone via BlueTooth connections. what would you recommend i do? Hi @jgump , If it works when connected to power but not when on battery only then I suggest that you replace the battery....
Chosen Solution HI there, the other day I spilled a small amount of water on my MacBook air’s keyboard while recording music using logic. I was able to wipe the water off without any visible damage. In a state of shock I stood there for a second, the laptop was on while this happened and I froze instead of shutting it off immediately. Nothing seemed to happen, I was able to finish the session on logic, which lasted at least another full hour, with no issues from logic or my MacBook....
Chosen Solution Can you use a S4 # i545 logic board on a I337 front frame? From what I can tel it would be fine to do this. You would probaby want to spend the little bit it costs and get the correct one though
Chosen Solution I press on the power button for 5-10 seconds but there is a delay in starting up. This is normal. After powering your speaker, it takes 1 minute to start up. The power sensor light will flash red and blue. Once it stays solid blue your speaker is ready to be used. I saw a YouTube video where a guy has this EXACT ISSUE. He said it never turns on....
Chosen Solution The CANON PIXMA MP280 panel displays “P07” error, but the computer which connects it, does not inform of any disfunction Eric, your printer needs to reset its ink counter. Step 1: Entering Service Mode While the printer is OFF, press and hold the Start/Stop button (Resume/Cancel in some other models). While holding the Start/Stop button, press and hold the POWER button. When the POWER LED (green light) lit, release the Start/Stop button (still holding the POWER button)....
Chosen Solution Hi! My new Philips 32PFS6402 turns on from stand-by itself with no reason. Philips helpdesk keeps continuing that: Update software! DONE! Is your Automatic Channel Update “off”? YES, OFF! Is your Channel Update Messages “off”? YES, OFF! Have you changed the batteries in remote? YES! Do you have Philips monitors in the same room with power sensors? NO! THIS OLD S… IN OTHER ROOM HAS EVER SEEN ANY POWER SENSORS!...
Chosen Solution I have tried a different outlet and a different power adapter and still nothing. Phone a friend with a charged battery. Would you describe how this started? I could be the DC-IN port, but we have to check if it will start from a battery before proceeding. Do you get any light on the power adapter? Check the tip of the AC plug to see if the tip is broken....
