Chosen Solution The slider that erases the writing on my screen doesn’t slide, what can I do about this? Do you hear anything rattling inside the creative center? Something small may have been lodged in front of the slider, preventing it from moving. Use this guide to access the slider. Hope this helps!
Chosen Solution Hi, I have purchased an A1304 Mid 2009 MacBook Air and I am having trouble with the WIFI card. It shows as No Hardware Found in the system tray and after searching online and eventually purchasing a new card (arrived and fitted today) It still shows the same message. Once I reset the PRAM by holding down alt>cmd>p>r until the second boot up sound the WIFI works fine. It shows in the system preferences and all the details of the card show up in the system report....
Chosen Solution Hi, I recently purchased a supposedly new Samsung Galaxy Note 5 (SM-N920T), T-Mobile branded but unlocked in the UK. Unfortunately I cannot get it to charge wirelessly, otherwise everything else works OK. I have tried various charging pads and leads with no success. I have wiped/cleared the cache and factory reset with no luck. I am assuming now it is a hardware fault? Can anyone suggest something else to try?...
Chosen Solution Hello! So i spilled a sticky sugary drink into both the usb c holes. I didnt notice it at first, i just cleaned the table and a little bit underneath the computer. The mac continued to run with no problems until the next day when i tried to plug it in, noticed the stickyness and it wouldnt charge. So i repeatedly inserted the charger, removed, cleaned carefully with damp paper around the usb c metal part, dried with paper, repeated the process until it felt normal....
Chosen Solution The remote won’t let me enter my pin and then if I click the select button it tells me my remote is not clickable - any suggestions? So… I just found out that holding the left, right , and menu buttons simultaneously for 5 seconds will reset the remote. Good luck!! Hold the menu button down on the remote. It will switch back to standard remote. Holding the menu button fixed my problem!...
Chosen Solution Hello, I swapped the display on an iPhone X and now you can see stripes on light backgrounds and low brightness. Could this be due to the spare part or rather to cables that are not properly connected? I used the iPhone X OLED Fix Kit. Thanks in advance, Tim Bro this is not the cable issue this is responsible for the cheap display try getting a refurbished i phone display or a better quality display....
Chosen Solution Replace the logic board & battery a few months ago and have had no problems whatsoever suddenly the computer shut down and then shut down after it starts up. When it’s cold & been off 12 hours I start it up and I can launch some programs but a few minutes later it shuts down. Could it be something as simply as a fan that died? Update (07/01/2021)...
Chosen Solution System powers up but only get black screen. Turned on system power button lit up all I see on monitor his black screen. I have pulled off the back and unplug the battery to try to reset the System but no help any ideas @rmaso321 start by attaching an external monitor and see what that displays. Should the image remain black, you may have trouble with your GPU circuitry on your motherboard....
Chosen Solution I don’t want to buy another darn camera what is wrong with this stupid one. It’s been sitting in its case by itself with a fresh pair of batteries Usually if a camera randomly shuts itself off its related to the battery . It can be a bad battery , or just the contact points could have dirt on them, use a cotton swab and isopropyl alcohol to clean the contacts in the camera and on the battery ....
Chosen Solution I had my PS3 controller disassembled so I could clean it. Once I had it cleaned and reassembled, I went to power it on and I could not get it to power on with the Sony button. I powered it on by plugging it into my PS3. It turned on with four blinking lights, but after ~15 minutes it never paired with the PS3. I disassembled it and clicked the reset button and re-seated the battery, but these didn’t make a difference....
Chosen Solution I can load pictures from my camera onto my A1103 Apple, but I can not load them onto a USB Device, A sheet pops un stating, “There is no available room to Duplicate” I have checked the hard drive and only 15 GB has been used, The total size of the pictures file is 516GB, so I think that there should be adequate room. I thought that it could be the fault of an interrupted Hard Drive...
Chosen Solution Unless I have headphones in, the only way I can be heard is to have headphones in. Any kind of headphone makes it work, not just the ones with a Mic Hi @treron , Can you hear OK on a call, using the phone’s ear receiver, without the headphones inserted? If you can, try starting the phone in safe mode and make or receive a call to see if the phone works normally, just to prove if it is a software problem or not....
Chosen Solution I press the power button, but nothing happens. How do I remedy this? You may have problems with either the screen or the battery. The simplest remedy is to replace the battery. If the battery is not the problem this screen will need replacing. Here is a link to the repair page Ematic FunTab 2 Battery Replacement
Chosen Solution Errotic and Jumpy trackpad Somehow my trackpad become jumpy.I’ve tried to clean the trackpad and my hand. But it stilll happen. it only happen when my Mac is connected to the internet. but not always when my my Mac is connected it happen (got it?). I’ve asked the apple store, but they dind’t know why either. Make sure that the trackpad is dry since this symptom of jumpy cursor....
Chosen Solution My screen has a blue line down the left side. Although small, it is very distracting. Every time i tilt the screen, multiple lines appear. I think it is because the screen is loose but have no idea how to fix it. Please help! As usual when troubleshooting a display the advice is to connect the computer to an external monitor to check if the problem is limited to the display assy or is caused by a faulty graphic card on the logic board....
Chosen Solution One day I do some wash, and everything is fine. The next day (or two) later, when I go to do wash, I see about 4 inches of water in the tub. The wash cycle runs fine again, and everything seems normal, but 24-48 hours later the 4 inches of water is there again. Sharon, sounds like the machine may have a faulty/ leaking solenoid fill valve. To check if this is the case, turn off water supply when tub empty, check the tub next day....
Chosen Solution wifi and bluetooth have stopped responding. Phone is in good shape and just replaced battery. Problem began before battery replacement. I would go through this area as that is where the WiFi/Bluetooth antennas are located, Check for proper connections and loose screws. Also look to see if there is any corrosion as water may have gotten inside but not enough to cause logic board damage. Has anything ever been done to the phone such as housing replacements or previous repairs?...
Chosen Solution My tablet is on, but I am unable to use it because my touchscreen is not working. I tried resetting my tablet, but when I turned it back on, my screen was still not responding to touch. Why won’t my tablet’s screen respond to touch? Hey Aaron, The problem could be as simple as an interfering screen protector. Try removing your screen protector or device case and see if the touch screen will work then....
Chosen Solution I have an 2008 iMac with 5gb ram and running OS X 10.11. And I was thinking about trying a Intel core 2 quad. Does anyone know if this processor will work with this iMac? According to this page that logic board should be socketed, so it should be physically possible. As to whether or not it will work, there doesn’t appear to be any information for that specific model, but it will depend upon whether the power supply can support it and whether the firmware has any restrictions within it....
Chosen Solution When I switch the camera on, the set time and date message comes on the screen. This has to be set before the message clears from the screen. The next time the camera on you have to go through the same procedure again. I have a similar camera (A570 IS) and mine has a second type of battery right beside the two main AA ones. It’s under a cover marked “CR1220” which refers to the type of that second battery....
