Posts

Chosen Solution Hello, From the sellins nd lhets missin ou would know wht i m tkin out. some kes re not workin wht to do? Assuming that nothing was spilled on the keyboard. Detach the key board, clean the connectors on the keyboard and the tablet and then reattach the keyboard, the connectors should look shiny when done. If something spilled on the keyboard then try wiping it with a slightly damp cloth, you do not want water to get into the keyboard....

Chosen Solution My new Roberts 10-600 stapler failed on the second day of use. I am installing a vapor/ insulation barrier in my garage and using this stapler for the job of attaching the barrier onto the 2X4’s. I shot approximately1000 staples and now the plunger that drives the staple into the wood will not retract.. You can manually drive the plunger back into the housing and it will fire one staple and stick again, It has been properly oiled after the initial use and now, the second day it worked for about 15 minutes and failed....

Chosen Solution Basically no. Laminated screens require a lot of professional tools and skills to replace. To replace just one, it definitely costs more than just replacing the whole screen unit.

Chosen Solution Duronic kitchen scales KS865 - wheatstone bridge strain gauge-based balance. The scales tare correctly, but when I place an object of known weight on it reads low. When I take that object off it does not quite return to zero. The scales have recently been dropped. I found that the load plate (top part) of the scales had become slightly twisted in its mounting (through the strain gauge) to the base of the scales....

Chosen Solution When I am in the Rock Band world and try to pull a Jimi Hendrix, my strum bar does not respond all the time. What do I do? If your strum bar is becoming less responsive than it should be, it needs to be replaced. Its sensors are getting worn out which means the simple press of a button will not be enough to fix the problem. You can find more information on this device including other issues you may experience through this troubleshooting page....

Chosen Solution My washer stops at the drain cycle and will not continue. Sometimes I can unplug it for a while and it will reset Cause 1 Drain Pump Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump and check the pump for obstructions. If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump....

Chosen Solution motorola a855 phone worked when activated but now stays whit with motorola sign. Cuts off and on also. Richard, check on here and see if that helps. If nothing works you can try to perform a hard reset Performing a hard reset will remove ALL data including the Google account, system data, application data, application settings, and downloaded applications. O With the device powered off, slide the keyboard open....

Chosen Solution I’ve taken my Macbook to Apple to repair my trackpad and asked them to check out why is heats up so much. They told me there isn’t any problems they can detect when they run their software checkup thing. So why is it heating up so bad? It also gets very very loud but it never turns off on me, its just loud and overheats alot! What can I do to fix this?...

Chosen Solution I’ve already tried charging my keyboard from the device battery, the battery shouldn’t be the problem. It seemed to stop working after I updated to Windows 8.1. Any help? If the keyboard stopped working after 8.1 update. It is most likely due to the system settings have been reset. The problem is most likely the filter key function. To fix this, disable the filter key and restart the device....

Chosen Solution I have an iPhone 5s that desperately needed a new battery. About a week ago, it turned off and when I plugged it in, it would go into an endless reboot cycle: the apple logo would appear, a red screen would flash for 1/4 second, screen goes black, and the apple logo appears again. From what I’ve read, this could have been a battery issue and/or a logic board issue....

Chosen Solution Two days ago I noticed when I connected my wall charger to my charging port on the phone that it.would connect show then a couple minutes later it will start vibrating and saying connect charger then it will charge like it’s engaging and disengageing Try another charging cable first (if this wall charger has a cable together and can not be separated then try another wall charger). If that does not work then your charger port is most likely damaged and needs to be replaced....

Chosen Solution The battery was recently replaced due to a problem that occurred when it was in use for a lengthy period of time. The bottom of the notebook became unusually hot swelling up the battery and making it impossible to close the casing. Therefore, i replaced the damaged battery with a new one, however, it does not charge at all. I’d also like to add that the notebook shuts off every time the power cord is not plugged in and the green indicator light lights up when it is plugged in....

Chosen Solution I just powered it on after a long time of no usage, and it worked! Except for the touch digitizer I couldn’t do anything except turn it on! Anyone have a solution? @joeofawe you could try a hard reset first and see if that will help. If it does not, you most likely have a bad digitizer. To replace that use this guide DigiLand DL801W Screen Replacement to get to it....

Chosen Solution i have a linksys router since 2 year . now its not working showing me yellow light after a power outage .i restarted and did everything which was possible . please help See if there is a reset hole that you stick a paper clip into. If so, do it.

Chosen Solution I don’t know what happened it was working a few minutes ago until suddenly it started going a little glitch then I tried to turn it off and it worked so I wanted to turn it on again but it isn’t working im charging it right now and I don’t know what to do I need this fixed in 3 days. Y.I.N.E try a power cycle first “There are multiple ways to reset your device if you are experiencing issues....

Chosen Solution I have an iPhone 6 and when it has a home button connected it wont boot but when I unplug the home button it will boot. It doesnt have its original home button and it has poor battery life. It’s either a bad home button or home button interconnect cable causing a short circuit stopping the phone from turning on.

Chosen Solution Since a drop and a repair service in a bad bad bad shop, the wifi, gyroscope and compass of my SE are not working anymore. I moved the logicboard (and only the logicboard) to a completly different iPhone SE and it is still not working. Which part beyond the plug on the Logicboard could be the reason for this? All of those functions have their own dedicated IC. The gyro and compass can be disabled when a logic board is cleaned with an ultrasonic cleaner....

Chosen Solution My iMac will not power up, I have to hit the power button many times before it powers up. Eventually it does and works OK. I try to leave it run all the time but sometimes it shuts down, I don’t know why. I do not shut it down but maybe someone else does, or maybe it shuts down on its own. I’m wondering if it could be the power supply or possibly power switch?...

Chosen Solution plug in all ports and none will work. wireless controller works fine Hi, Are you talking about plugging a wired controller into an Xbox or a PC? If it is into a Xbox and it doesn’t work, here is a link that shows how to connect a controller into a PC so that you can test whether it is the wired controller or the Xbox that is faulty. https://support....

Chosen Solution My Iphone 7 turned itself off overnight. When i try to turn it on, it won’t start. Pressing Power button + Vol Down won’t do nothing. When connected to computer, iTunes detect’s it and says it needs to do a repair but stops at half and gives error 4014. 3Utools detects the phone as being in DFU mode. When trying to flash it, the phone finally wakes, shows apple logo for about 8 seconds, (3Utools says it’s in recovery mode at this moment) but as soon as a spinning wheel appears under the apple, the screen turns black again (although you can see it stays with backlight), 3Utools says it’s disconnected for about 5 seconds and after that returns to DFU mode....