Posts

Chosen Solution turn on normal cycle, was fine for about 3-4 min, started to beep and flash H and F in display window I believe that those are error codes….isn’t it great to have a washer that checks itself :) anyhow some of the codes are “F20” (Water Inlet Problem—no water or insufficient water supply) Select STOP twice to cancel the cycle. Unplug washer or disconnect power. “F21” (Drain Problem)Select STOP twice to cancel disconnect power....

Chosen Solution This is what my display shows: I’ve replaced the LCD, LVDS cable, LCD temp sensor. I’ve also try plugging in an external monitor and it shows perfectly no signs of the faint image. When I boot the system display it randomly shows a normal image sometimes but when it does, the system powers off or goes to sleep. I can hit the space bar to wake it up sometimes but once I restart the system, it goes back to the fainted screen....

Chosen Solution Hello, I currently changed my battery, lighting connector and headphone jack, along with my display. I followed the guild and videos and made sure everything was correct. But my phone is heating up on the top right side and its charging slow in a way? The iPhone contain several thermistors designed to measure and monitor the heat on the logic board and if anything goes out of spec, you will see an error message....

Chosen Solution Hi,today i wanted to fix my front camera for my iphone 6 plus After that i tried turning on the phone but it wouldnt turn on I disconnected and reconnected the flex cable for battery but no changes But when i connect only the left side of the connector it turns but randomly restarts When i connect both properly it turns off instantly as show in the video below https://youtu....

Chosen Solution I dropped my camera in the beach with the lens facing the ground. I immediately removed the memory and the batteries. I let it dry for hours.When I try to turn it on the screen was only flashing but there was no display and the 3 lights (Battery light, the front light when you capture a image and the memory light) are turned on but the lens are not moving and the buttons are not functional too except the power button....

Chosen Solution Hi, I’m trying to understand what is going on with my Macbook Pro early 2015 (820-4924). I don’t have any power the PP18V5_DCIN is not present on the board. I have something around 600mV with a pulse of 4V that I can see with a scope, but nothing else. Which also mean I don’t have any rails present to, am I right? I checked voltage at the connector of the MagSafe 2, so it is not a problem with the fuse....

Chosen Solution my phone suddenly got switched off and from then, when i am trying to open it, its showing an error message -“ERROR:unable to find a bootable option. press any key to shut down.” This is probably due to a problem with the OS. I would recommend using the Nokia Software Recovery Tool to re-install the factory image. It can be downloaded direct from Microsoft here: https://support.microsoft.com/en-us/help… It’s fairly simple to use....

Chosen Solution 2001 Chevy Blazer LT 4WD V6 4.3L EDIT3: Since I replaced the switch, I’m led to believe that the only other things it could be are either the AC accumulator or the HVAC actuator. The actuator failing is a common issue with this type of car according to online resources, however, that is the more expensive of the two options. I may have to replace the accumulator to see if that works since it only costs $30....

Chosen Solution As I was finishing up using my camera, upon powering off, I noticed the camera lens will not retract back into the camera. This makes it unable to close the sliding cover feature over the lens. Is there any explanation for this issue? Fortunately, this is a very common issue in most cameras. There a few reasons as to why your camera may not be retracting the lens however, most solutions are quite an easy fix....

Chosen Solution i put a cd player in my car before and switched it out for a newer cd player.now that i put a new one in it won’t work.i double checked to make sure all wires where right and fuses…What else could it be for it not to work? First thing I would do is test the power wire to the stereo with a volt meter and see if you are getting 12 volts from it and at the same time make sure the Ground source is also working, if that is good I would look for a fuse that is in the stereo itself and see if it’s good, if that’s all good then I would have to think the stereo may be bad....

Chosen Solution == How do I fix this problem?== I was given a Philips PhotoFrame Model No.:8FF2FPW/37 When I plug the digital photoframe into the outlet and push the power button it does not turn on, the screen remains black. Needs a firmware upgrade - Your phtoframe has shut down into a power save mode as yo umay not have used it for a long time. Upgrades on the Phillips web site...

Chosen Solution I was working out at the gym and accidentally dropped a 50 lbs dumbbell on my phone. My screen cracked (left upper corner) and bottom 3/4 of the screen was not visible. I went to the local repair shop (not Apple) and got my screen fixed for $130. The touch screen works now and I have no problem with using my iPhone. However, my wifi is grayed out and bluetooth doesn’t work....

Chosen Solution I got the Wii out of storage. I set it up and it worked. I did not use the Wii until a week later(now). I press the power button, and it remains completely blank, not green or red. (I have tried unplugging every thing and letting it sit for a half hour.- the Wii has never been modified) pls help soon! thanks. the wall outlet I had it plugged into was rotting apart....

Chosen Solution Apple MacBook Pro “Core i7” 2.3 15" Late 2013 (DG) Specs Retina Late 2013 15" - ME294LL/A - MacBookPro11,3 - A1398 - 2745 I’m asking this because I had three abscessed teeth pulled yesterday, on pain medication and thinking is just not all that good today ;=() @danj I know I know the answer but it’s not coming to me. I replaced a slightly water damaged keyboard on this machine about a year and a half ago....

Chosen Solution Phone was not recognized on mac nor was it recharging off the wall using multiple apple cords so I replaced the battery. It was able to recognize on mac noticed it had shown the little lighting bolt next to bat. % in top right corner but it was not recharging. I did not thing to do a “hard” reset but the phone is now dead. I did a little research and found that a pin in the dock connector could be bad but I have not yet dismantled my phone dock connectors look to be fairly inexpensive any other suggestions?...

Chosen Solution How do I remove the back cover to access the wireless card? I have look at similar fixes but the 955 seems different @jaxrthedog check this video out. It will at least get you into your laptop. It’s a definite PITA to work on those. Typical Toshiba. No service manuals available and 100% opposed to DIY repairs. Hi @jaxrthedog , Have you proved that it is a card problem and not a software problem?...

Chosen Solution My Blu phone life one 3x is compatible with straight talk and straight talk is saying my phone is not compatible with their Network. Can any help with figuring out why my phone is not compatible. Are you using the same sim card that you had in your old phone. If you are what kind of device was it . Blu phone are unlocked GSM devices. Straight talk used both GSM and cdma network....

Chosen Solution I can’t do a factory restore or update my iPhone 6 Plus while connected to iTunes. I keep getting a error 53 message. I changed my screen recently and during the repair I tore the wafer cable to the home button, so I just changed the Touch ID/home button. I heard that my fingerprint would no longer be able to be used which it wasn’t but why would that prevent me from doing an upgrade and ultimately being stuck on iTunes connect screen?...

Chosen Solution The small piece on the side of my xbox one that is used to sync controllers snapped in half, broke off. Along with that issue, when it was able to be pushed it felt like a piece was missing behind it so really felt like i was pressing nothing at all. What can i do? Recently got it back to have hard drive replaced. Any way to fix? Or connect another way?...

Chosen Solution Have tried external. speakers yet no audio @osuji besides all the excellent points made by @jayeff you do want to disconnect everything from your TV’s inputs. Then unplug the set for a while pushing and holding the power button for a short while as well. After that. Connect one input source and start your TV. See if that changed anything. If none of the above worked you are possibly having an issue with the amp out for your TV....