Posts

Chosen Solution I have a Troybilt TB635 EC. Recently I replaced primer bulb, fuel lines, and carburetor. I double checked that the three lines from primer bulb are correct and that there are no leaks where they connect to bulb or carb. However, when I press primer bulb about 5-6 times, gasoline will start coming out of the air filter port. Need help with this one please. You may have already done this but here is what I would do in this case....

Chosen Solution Why is the contro lock on? My wshing machine does not work at this time. What do I need to do to fix it? Try unplugging it for 5 minutes and then plugging back in. This failing try this answer: “Contol locked” light is on. Nothing else responds..

Chosen Solution it gets to 0 hour later 35 Hi @randbrook , There may be a problem with the defrost timer in the fridge. It manages the timing for the auto defrost system. Part #648 in the Compartment Separator parts diagram box.

Chosen Solution The washer cycles through but stops randomly. Sometimes it goes for 8-9 minutes then stops for 30-45 minutes at a time. Sometimes it only goes for 10-15 seconds before stopping again. It smells like some sort of rubber burning or something when it stops mid-cycle. Any ideas will help. Thanks Most Frequent Causes for Washer stops mid cycle Cause 1 Lid Switch Assembly The lid switch assembly prevents the washer from spinning when the lid is open....

Chosen Solution I recently managed to get the moped running properly, albeit for only a short time. Things were looking up: I replaced the spark plug, cleaned out the exhaust, adjusted the idle / fuel screws, and even replaced the brakes (I can stop now!). So everything was looking good. I was test-riding it after a short hiatus, and the moped was running fine. Near the end of my ride, I stopped at an intersection to make a left turn....

Chosen Solution So basically, my iPhone died yesterday and I put it in the charger. Before it died, it had some issues with the charger going in the whole, it was like it couldn’t go in all the way and I had to bend it at a crazy angle for it to charge. Nothing was wrong with the charger, I tried it on other devices and it worked fine. So I kept it there for a few hours and it was still showing the red battery screen, nothing else....

Chosen Solution update the phone and the phone wont work keep saying failed to set up mount.. Hello Latonya Gillespie, Press and hold the power button until phone turn off After 20 seconds press and hold Power+ Volume Up to enter Recovery modeuse 5th option ( update from cache - if the previous version not update properly this option will help you to fix the phone) if above step not works select option 4 (Update from SD card - your phone support only OTA updates so update could be store at memory on your phone - this step will help you to update back your phone Non of above not works for you, just try 3rd Option ( Wipe data /Factory reset ) Hope this answer will help you to fix your device your self

Chosen Solution Why won’t my flat iron turn on? There are several reasons why your flat iron will not turn on. Check the cord for any frayed or exposed wires. If that is fine, it could either be a faulty on/off switch or a blown fuse. See our troubleshooting guide here for more information. Here are the possible solutions that might help for your flat iron as mine: loose wire connectionfaulty power cordfaulty curcit/ boardfaulty power source and a few more important steps are indetail explained on a troublshooting help article....

Chosen Solution Hello, My MacBook Pro will not power up. Here’s the story of what has happened so far. My battery had the status of SERVICE BATTERY SOON. Then changed to REPLACE NOW. I didn’t know it had changed and my computer unexpectedly shut off. It was able to turn on again multiple times, but wouldn’t remain on. After a while it just stayed dead. Keep in mind that my power adapter was frayed....

Chosen Solution Hey forum, Earlier today I tried to hook my MacBook Pro 13” Mid 2010 to an external monitor. The monitor was plugged into a surge protector, and my DVI cable was plugged into the Mac. As I tried to plug the other end into the monitor, an arc formed between the DVI connector and the cable. Long story short, this killed the Magsafe charger I was using. I tried to plug my backup into the Mac, but the Mac wouldn’t accept a charge, and the Magsafe light was stuck on green....

Chosen Solution My tf103c screen won’t rOtate and have:-) No sound can aNyone :-)help me . Hi, With regards to screen rotate have you checked that the following setting is ticked? Settings > Screen > Auto Rotate. Also the screen won’t rotate if the keyboard is docked. With sound, have you tried using headphones to see if there is sound? Update (04/17/2016) Hi, Try the following. Use the tablet’s backup feature to backup your tablet....

Chosen Solution My Sony Walkman the motor runs the batteries don’t work but with a cable it does when I push play one of the spindles turns but not the other I think the problem is that the gears aren’t connecting properly how do I fix it can I fix it Kaysie Elvir you should only have one spindle working. The right pulls the tape during play and forward the left for the rewind....

Chosen Solution it wont let me tap the wifi setting and it says no wifi anthony, here is my answer from a question very similar to yuors “here is what Apple suggest. try this first “Resolution If you encounter this issue, try the following steps and attempt to enable Wi-Fi or Bluetooth after each one. Verify that Airplane Mode is turned off. Update your iOS device to the latest version of iOS....

Chosen Solution My Acer R11 R131T won’t charge, or power on without being plugged in, but tells me the battery is there and gives me a percent. It says “40%, Plugged in, not charging” at the moment, but it’s been going down slowly. I’ve tried the power reset by pressing the button on the bottom and waiting a few minutes (overnight). I’ve also tried other chargers, including new chargers. Any tips or help would be nice....

Chosen Solution I did a.motherbiard swap on.my 5 c and.wont turn on Hmm.. Well, first things first. Check all your connections, make sure everything is where its supposed to be. If you still have the same issue, try to turn it on, while the phone is “open” and see if the backlight is still on. If not, then unfortunately tear it apart, try the old logic board, see if it will turn on, with the old one....

Chosen Solution I have a work horse gt-1642 and the read end is stuck in between ranges. The wheels are locked up solid and when I put the belt on and let the clutch out it stalls the engine. Its on a riding mower. Made from 1982-1983. I found the problem. It had water that froze in the rear end locking it up I don’t know what a “work horse” is....

Chosen Solution My MacBook pro and the left speaker is distorted. I’ve tried resetting the NVRAM and SMC still nothing. I’ve Tried plugging in the headphones and its the same issue, its distorted on the left earphone. Tried changing frequency in the Midi Setup still and the issue still persists. The Startup sound is distorted also. At first i Had OS sierra installed when the issue occurred, I tried updating to High Sierra and still nothing....

Chosen Solution Could someone please tell me that why I am not getting sound from right earplug but I can hear sound from left ear plug. Last night it was working well and in the next morning when I just got up and plugged in ,right ear plug wasn’t working. How will I repair it? Have you tried to use them in another device? Same Problem? If so, under warranty? Contact Beats for replacement....

Chosen Solution Internal drive crashed and now I’m using an external hard disk. Still speaker is not working. I would recommend fixing the internal drive issue first. This model comes with a custom blade SSD. Here’s the IFIXIT guide to gain access to it: MacBook Air 11" Early 2014 SSD Replacement. IFIXIT sells Apple SSD units but you can use a 3rd party SSD which will be a bit cheaper for the larger sizes....

Chosen Solution Why does my washer stop during spin cycle with code UL displayed? If the “UL” unbalanced load error comes up there is a mechanical issue or bad CCU. Are you getting a banging sound? martina2020 besides the things that @mayer mentions, there are a few things that can cause this. Check the suspension kit of the drum to make sure that it is not excessively loose. Most commonly for this model is a failed rotor position sensor or a cracked stator on the motor....